Technical Brief

Evaluation of a Prototype Hybrid Vacuum Pump to Provide Vacuum-Assisted Suspension for Above-Knee Prostheses

[+] Author and Article Information
Matthew J. Major

Jesse Brown VA Medical Center,
Northwestern University Prosthetics-Orthotics Center,
680 North Lake Shore Drive, Suite 1100,
Chicago, IL 60611
e-mail: matthew-major@northwestern.edu

Ryan Caldwell

Scheck and Siress Orthotics and Prosthetics,
Northwestern University Prosthetics-Orthotics Center,
680 North Lake Shore Drive, Suite 1100,
Chicago, IL 60611
e-mail: ryan.caldwell@northwestern.edu

Stefania Fatone

Northwestern University Prosthetics-Orthotics Center,
680 North Lake Shore Drive, Suite 1100,
Chicago, IL 60611
e-mail: s-fatone@northwestern.edu

Manuscript received January 13, 2015; final manuscript received April 3, 2015; published online August 6, 2015. Assoc. Editor: Carl Nelson.

J. Med. Devices 9(4), 044504 (Aug 06, 2015) (4 pages) Paper No: MED-15-1003; doi: 10.1115/1.4030507 History: Received January 13, 2015

Vacuum-assisted suspension (VAS) of prosthetic sockets utilizes a pump to evacuate air from between the prosthetic liner and socket, and are available as mechanical or electric systems. This technical note describes a hybrid pump that benefits from the advantages of mechanical and electric systems, and evaluates a prototype as proof-of-concept. Cyclical bench testing of the hybrid pump mechanical system was performed using a materials testing system to assess the relationship between compression cycles and vacuum pressure. Phase 1 in vivo testing of the hybrid pump was performed by an able-bodied individual using prosthesis simulator boots walking on a treadmill, and phase 2 involved an above-knee prosthesis user walking with the hybrid pump and a commercial electric pump for comparison. Bench testing of 300 compression cycles produced a maximum vacuum of 24 in-Hg. In vivo testing demonstrated that the hybrid pump continued to pull vacuum during walking, and as opposed to the commercial electric pump, did not require reactivation of the electric system during phase 2 testing. The novelty of the hybrid pump is that while the electric system provides rapid, initial vacuum suspension, the mechanical system provides continuous air evacuation while walking to maintain suspension without reactivation of the electric system, thereby allowing battery power to be reserved for monitoring vacuum levels.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.


Board, W. J. , Street, G. M. , and Caspers, C. , 2001, “A Comparison of Trans-Tibial Amputee Suction and Vacuum Socket Conditions,” Prosthet. Orthotics Int., 25(3), pp. 202–209. [CrossRef]
Goswami, J. , Lynn, R. , Street, G. , and Harlander, M. , 2003, “Walking in a Vacuum-Assisted Socket Shifts the Stump Fluid Balance,” Prosthet. Orthotics Int., 27(2), pp. 107–113. [CrossRef]
Gerschutz, M. J. , Denune, J. A. , Colvin, J. M. , and Schober, G. , 2010, “Elevated Vacuum Suspension Influence on Lower Limb Amputee's Residual Limb Volume at Different Vacuum Pressure Settings,” J. Prosthet. Orthotics, 22(4), pp. 252–256. [CrossRef]
Beil, T. L. , Street, G. M. , and Covey, S. J. , 2002, “Interface Pressures During Ambulation Using Suction and Vacuum-Assisted Prosthetic Sockets,” J. Rehabil. Res. Dev., 39(6), pp. 693–700. [PubMed]
Klute, G. K. , Berge, J. S. , Biggs, W. , Pongnumkul, S. , Popovic, Z. , and Curless, B. , 2011, “Vacuum-Assisted Socket Suspension Compared With Pin Suspension for Lower Extremity Amputees: Effect on Fit, Activity, and Limb Volume,” Arch. Phys. Med. Rehabil., 92(10), pp. 1570–1575. [CrossRef] [PubMed]
Hoskins, R. D. , Sutton, E. E. , Kinor, D. , Schaeffer, J. M. , and Fatone, S. , 2014, “Using Vacuum-Assisted Suspension to Manage Residual Limb Wounds in Persons With Transtibial Amputation: A Case Series,” Prosthet. Orthotics Int., 38(1), pp. 68–74. [CrossRef]
Traballesi, M. , Averna, T. , Delussu, A. S. , and Brunelli, S. , 2009, “Trans-Tibial Prosthesization in Large Area of Residual Limb Wound: Is it Possible? A Case Report,” Disability Rehabil. Assistive Technol., 4(5), pp. 373–375. [CrossRef]
Traballesi, M. , Delussu, A. S. , Fusco, A. , Iosa, M. , Averna, T. , Pellegrini, R. , and Brunelli, S. , 2012, “Residual Limb Wounds or Ulcers Heal in Transtibial Amputees Using an Active Suction Socket System. A Randomized Controlled Study,” Eur. J. Phys. Rehabil. Med., 48(4), pp. 613–623. [PubMed]
Arndt, B. , Caldwell, R. , and Fatone, S. , 2011, “Use of a Partial Foot Prosthesis With Vacuum-Assisted Suspension: A Case Study,” J. Prosthet. Orthotics, 23(2), pp. 82–88. [CrossRef]
Carvalho, J. A. , Mongon, M. D. , Belangero, W. D. , and Livani, B. , 2012, “A Case Series Featuring Extremely Short Below-Knee Stumps,” Prosthet. Orthotics Int., 36(2), pp. 236–238. [CrossRef]
Kahle, J. T. , and Highsmith, M. J. , 2014, “Transfemoral Interfaces With Vacuum Assisted Suspension Comparison of Gait, Balance, and Subjective Analysis: Ischial Containment Versus Brimless,” Gait Posture, 40(2), pp. 315–320. [CrossRef] [PubMed]
Kahle, J. T. , and Highsmith, M. J. , 2013, “Transfemoral Sockets With Vacuum-Assisted Suspension Comparison of Hip Kinematics, Socket Position, Contact Pressure, and Preference: Ischial Containment Versus Brimless,” J. Rehabil. Res. Dev., 50(9), pp. 1241–1252. [CrossRef] [PubMed]
Komolafe, O. , Wood, S. , Caldwell, R. , Hansen, A. , and Fatone, S. , 2013, “Methods for Characterization of Mechanical and Electrical Prosthetic Vacuum Pumps,” J. Rehabil. Res. Dev., 50(8), pp. 1069–1078. [CrossRef] [PubMed]
Otto Bock HealthCare, 2009, “Harmony P3 Instructions for Use,” Otto Bock HealthCare LP, Duderstadt, Germany.
Caldwell, R. J. , Hansen, A. H. , Wood, S. M. , Chen, W. , Radcliffe, R. A. , Yngve, K. A. , Kuhar, B. E. , Nelson, A. J. , and Nickel, E. , 2012, U.S. Patent No. 13/529,833.
Major, M. J. , Twiste, M. , Kenney, L. P. , and Howard, D. , 2011, “Amputee Independent Prosthesis Properties—A New Model for Description and Measurement,” J. Biomech., 44(14), pp. 2572–2575. [CrossRef] [PubMed]
Major, M. J. , Kenney, L. P. , Twiste, M. , and Howard, D. , 2012, “Stance Phase Mechanical Characterization of Trans-Tibial Prostheses Distal to the Socket: A Review,” J. Rehabil. Res. Dev., 49(6), pp. 815–829. [CrossRef] [PubMed]


Grahic Jump Location
Fig. 4

Results from (a) bench testing, (b) in vivo walking with simulator boots (the first and second dashed vertical lines represent the initiation of the electric system and walking, respectively), and (c) in vivo walking of a transfemoral prosthesis user with a commercial electric pump (Ohio WillowWood LimbLogic) and the hybrid pump

Grahic Jump Location
Fig. 3

Location of the hybrid vacuum pump for use within a transfemoral prosthesis. Pyramid adaptors fixed to proximal and distal ends of the pump housing were used for installation of the pump between the socket and knee joint, respectively.

Grahic Jump Location
Fig. 2

Walking simulator boots. Prosthetic components attach distal to the foot plate and mimic transtibial prosthesis use.

Grahic Jump Location
Fig. 1

Schematic of the hybrid pump design. Constituent parts include: (a) proximal female pyramid adapter, (b) distal male pyramid adapter, (c) proximal housing plate, (d) distal housing plate, (e) bladder pump (mechanical system), (f) electric pump (electric system), and (g) threaded posts (×4). The threaded posts act as guide rails during cyclical compression and extension of the bladder. The solid arrows indicate air flow from the socket volume during operation.



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In